Bong Rip Combustion be gone! The Thermal twist is here!
Works great with a Plankton bong!
https://vapewidgets.com/products/plankton-upright-bubbler-upline
The Thermal Twist Ball-less Dry Herb Vape, was designed by recommendedvapesupplies.co.uk in collaboration with Crossing Tech to bring a highly effective and competitively priced injector vape to the market, diffuser bowl coming soon!
Removing the need for balls entirely they have designed this with vortex airflow and a metal core! Available in either SS316 Stainless Steel or Grade 2 Titanium. The Vortex airflow removes the need to stir your bowl when used with around 0.1.5-0.2g loads as the hot air does the work for you, removing one additional step while vaping! Just load in a one SQP of herb, place the housing on the bowl, inhale, then watch it spin up and settle in to place! There's no need to tamp your bowl as the airflow will do this for you too! Due to the spinning airflow the Thermal Twist also makes an excellent micro-doser, happily vaporizing down to around 0.05g (we haven't tested with less... it would still vape less).
Designed with a simplified user experience in mind, the Thermal Twist comes fully set up with a handle installed on the heater coil and the housing fully set up, making for a plug and play experience without the possibility of spilling balls (as there are none) or mis-installing the handle during setup! Plug the heater into the front of the PID, the power adapter/plug into the back, turn it on, set your temp and it's ready to go (initial burn off cycle advisable)! The Stand has been designed to provide minimal contact with the housing, meaning the heat stays where it should be, inside the housing and not being transferred into your stand, or worse, into the surface below!
Capable of providing anything between low temp terpy hits, to thick clouds. The Thermal Twist has fairly fast vapor production and exceptionally smooth vapor!
This kit comes with everything needed to get started, aside from a glass Rig or Bubbler (optionally available) and herb.
Suggested set temperature range on the PID: 280- 390c (526f-734f) but as with everything... use it as you like it!
- Titanium provides slightly better flavor and is a lighter weight material
- Stainless Steel provides slightly smoother vapor
Please check out this video if you're interested in an in depth review.
Also featured on Troy and Jerry Think Dank
Includes
- Thermal Twist Injector (GR2 Titanium)
- Crossing Technology Micro PID (1c/1f) (CE/ROHS Certified)
- 20mm Heater Coil with Silicone Handle Pre-installed (220v)
- Pre-installed Heat Guard for the Thermal Twist Housing
- Glass Bowl with a Side-Carb (approx. 0.4g max capacity) - 14.4mm Male Joint Bowl
- 14.4mm to 18.8mm Male Adapter
- Keck Clip
- Steel Stand
- SQP - Scoop and Tamper
- Wood Cleaning Brush
- Spare Screens
- UK 3-pin Plug
- Instructions Sheet
Spare Parts Available Here
Warranty Info
- We provide a one year warranty on the PID controller and Heater Coil.
- Broken glassware should be reported on arrival. Please photograph this in it's packaging so improvements can be made where required.
Usage notes
- If using the 14mm bowl with the keck clip and 18mm adapter, when you install the 14mm bowl into the 18mm joint give it a little push and twist to help the two joints lock together, then install the keck clip. This will help prevent the joints rotating unintentionally
- Unless using this setup with the diffuser bowl (not included, coming soon) it is not advisable to leave the Thermal Twist housing on the bowl. Place the housing on the bowl, inhale, remove the housing setup and place it safely on the stand
- To avoid the herb being additionally compacted there is a side carb/stopper integrated into the bowl, you can remove this stopper to assist in clearing the bubbler of excess vapor
- The Heat Guard extends past the bottom of the injector housing for maximum protection, this also helps align the bottom of the injector housing into your bowl for added convenience and makes it very hard to miss! We only mention this as those of you who are already using injector vapes will be unused to this system as with most devices you have to watch closely to ensure the injector is neatly placed into the bowl.
- The Thermal Twist works really nicely with hash (not bubble), if you double up the mesh screens then break up the material small but not too finely and place some on the top screen it's pretty effective.
- The Diffuser bowl (coming soon) is also great as you can place some into the screen, then place another screen on top to trap it inside the bottom screen. With a little heat soak especially this is highly effective.
Please perform a burn off cycle on the housing before installed. Once set up, set your PID to 380C (734f) and allow any manufacture residues to burn off. Give it 5 minutes before first use.
Fun features
The Thermal Twist can be used with the 18mm C/C Quartz Cap vaporizer by the rogue wax works. Just pop the housing over the top of the glass chamber section and use your Quartz Cap vaporizer as a diffuser style bowl! With or without heat soak! If heat soaking you can adjust the mesh screen inside the Quartz Cap chamber so that it sits higher up for a full hybrid experience. You will want to reduce the temps on your pid by around 70-100c if doing this.
We are working on a glass diffuser bowl for the Thermal Twist... but in the meantime... this goes... It really goes!
